3D puff digitizing for raised lettering that stays crisp

Send your design and tell us the garment. A digitizer builds the file for foam, with thick letters, full coverage and clean edges, so the raised stitching looks sharp and no foam shows. You review a digital proof before you order.

  • Built for foam, not flat thread
  • Caps, beanies and hoodies
  • Letters sized so foam stays covered
  • Free revisions until you approve
Flat red IRON ANVIL lettering with a gold GARAGE & CUSTOMS line on a white background
IRON ANVIL lettering stitched in raised red 3D puff on a dark twill cap front, with a flat gold GARAGE & CUSTOMS line below
3D puff artworkStitched 3D puff

What is 3D puff digitizing?

The 3D puff digitizing service turns your design into a stitch file for raised embroidery. A digitizer builds the file around a layer of foam: dense capping stitches cover the foam, and a cut line lets the extra foam tear away clean. The result is bold letters or shapes that stand out from the fabric.

A flat embroidery file does not work for 3D puff. Foam needs thicker shapes, tighter stitches and a different sewing order, so puff needs its own file.

On this page

What 3D puff digitizing means for your design

3D puff is raised embroidery. A thin layer of foam sits under the thread, and dense stitches cover it, so the letters stand out from the cap. It reads bold from far away, which is why caps and hoodies use it.

Foam changes how a design must be built. The digitizer makes letters thick enough to hold the foam, sets stitches that cover it fully, and adds a cut line so the extra foam tears away clean.

What you send

  • Your logo or design file, in any format you have.
  • The garment: structured cap, beanie, hoodie or another.
  • The placement and the width you want.

What you get

  • A stitch file built for foam, in your machine's format.
  • A digital proof to check before you order.
  • Free revisions until you approve the sew-out.

Why 3D puff needs its own file

A flat file sewn over foam looks rough and shows the foam. Four things change.

  • Foam needs thick shapes

    Thin lines cannot hold foam. We make strokes thick enough to carry it, and stitch fine details flat.

  • The foam must be fully covered

    Dense capping stitches run across the foam, so it is hidden and the edges look smooth and rounded.

  • The extra foam must tear away clean

    A cut line around each shape perforates the foam, so the waste pulls away and leaves a neat edge.

  • The sewing order is different

    The machine sews the cut line, stops so you can place the foam, then stitches the cover. We set that order.

How 3D puff digitizing works

Every puff order follows the same four steps. There is no account to create and no minimum order.

  1. Send your design and garment

    Fill in the quote form. Upload your logo and tell us the garment, placement and width.

  2. We check the design for foam

    We view the design at real size, find thin lines and small text, and decide which parts can be raised. Then we send your price.

  3. Review your digital proof

    A digitizer builds the file by hand and a second one checks it. You see the design at real size, with the raised parts marked.

  4. Approve and sew

    Once you approve, we send the final file in your machine's format. If the sew-out needs a change, send a photo.

What works in 3D puff

Puff looks best when the design is bold and simple. We check four things on every file.

Design partWorks wellWhat we do
LetteringThick block, slab or sans lettersWe keep strokes wide and spacing open. Script and thin fonts are changed.
ShapesSimple, rounded shapes with room insideWe round sharp corners and close tiny gaps.
Small detailsFew, and kept flatThin lines and small text are stitched flat.
ColorsOne to three raised colorsEach raised color is its own foam step.

Not sure if your design will puff? Send it and we will tell you.

Before and after: 3D puff in thread

Drag the needle to compare each original design with its stitched sample.

Flat North Star Skate Co. artwork on a white background: an orange star above orange block lettering, with a gold SKATE CO. line below
North Star Skate Co. design stitched on a navy cap front: a raised orange 3D puff star and NORTH STAR lettering above a flat gold SKATE CO. line, with the center seam showing

Design fileStitched

Raised name and star on a navy cap

A skate brand sent flat artwork. We thickened the letters and star and kept the small line flat.

  • Letters widened so the foam is covered.
  • Star points rounded so foam tears clean.
  • Small gold line stitched flat.
Size
4 in wide
Stitches
12,600
Fabric
Navy twill cap
Files
DST, PES

Sample designs shown for layout preview.

Where 3D puff works best

The garment decides how much the foam can do.

PlacementTypical sizeWhat to expect
Structured cap frontAbout 1 to 2 inches tall, up to 4.5 inches wideThe best surface for puff. The stiff front holds the foam.
Beanie cuff2 to 3 inches wideKnit stretches, so we keep the shape bold and simple.
Hoodie or sweatshirt chest3 to 5 inches wideThick fleece suits puff, with a stitch base under the foam.
Dad hat or soft capAbout 1 to 1.5 inches tallA soft front can pucker under foam. We tell you if it is a poor fit.

Sizes are examples. Tell us the garment and the width you want and we fit the file.

What to send for a 3D puff design

The cleaner the file, the faster and sharper the result. You do not need a perfect file to start.

Best to send

  • A vector file: AI, EPS, SVG or PDF
  • A PNG with a clear background, at least 1,500 pixels wide
  • The garment type and its color
  • The placement and the width you want
  • Thread and foam colors, if you have them

Also works

  • A JPG from your website or social page
  • A photo of a puff garment you already have
  • A sketch or a photo of the design

3D puff digitizing prices

The price depends on design size, detail and stitch count. These are starting prices. Your quote is the exact figure.

DesignWhat it meansFrom
Simple puff textOne word or two short words, one color, up to 4 inches wide$18
Puff text with a shapeLettering plus one simple shape or icon$26
Puff with flat detailsRaised parts plus small flat text or lines in other colors$34
Extra raised colorEach added foam color in the same design$8

Rush service is available. Flat cap embroidery is priced on the cap and hat page.

3D puff designs we have digitized

A few finished designs, stitched from the puff files we built.

  • Titan Gym logo stitched on a black cap: a raised white 3D puff dumbbell above raised white TITAN lettering, with a flat red GYM line below
    Titan GymA raised white dumbbell and name on a black cap.
  • Westside Hornets logo stitched on a navy cap: a large raised gold 3D puff W between flat cream WESTSIDE and HORNETS lettering
    Westside HornetsA bold gold W with flat lettering on a navy cap.
  • Mile High Trucking logo stitched on a green cap: raised white 3D puff MILE HIGH lettering above a gold bar and a flat gold TRUCKING CO. line
    Mile High TruckingRaised white lettering and a flat gold line on a green cap.
  • Crown City Barbers logo stitched on a maroon cap: a raised gold 3D puff crown above flat cream CROWN CITY lettering and a flat gold BARBERS line
    Crown City BarbersA raised gold crown with flat lettering on a maroon cap.

Sample designs shown for layout preview.

Have a puff design to stitch?

Send your design and the garment. Get a price and a digital proof before you order.

3D puff digitizing questions

Can't find your answer? Send a message with the Get a Quote form and we will reply.

How much does 3D puff digitizing cost?

3D puff digitizing starts at $18 for a simple design, $26 for text with a shape and $34 with flat details added. Your quote is the exact price.

How long does 3D puff digitizing take?

Most puff files are ready in about 24 hours. A large or detailed design can take a little longer. Rush service is available.

What is the difference between 3D puff and flat embroidery?

Flat embroidery sits on the fabric. 3D puff puts foam under the thread, so the letters stand out. It needs thicker letters and different stitches, so it is built as its own file.

How small can 3D puff letters be?

About 0.3 inch tall is a safe minimum, with strokes at least 2 mm wide. Smaller letters cannot hold the foam, so we make them larger or stitch them flat, and show you in the proof.

Which garments work best for 3D puff?

Structured caps work best, because the stiff front holds the foam. Beanies, hoodies and jackets also work. Soft dad hats can pucker, and we tell you if the design is a poor fit.

Can I mix 3D puff with flat embroidery?

Yes, and it often looks best. Bold letters or the main shape are raised, and small text or fine lines are stitched flat beside them.

Why does foam show through my puff embroidery?

Usually the letters were too thin or the cover stitches were too far apart. Send us a photo and tell us the garment, foam and machine, and we adjust the file. Revisions are free until you approve the sew-out.

Which file format should I ask for?

Ask for the format your machine reads. DST is the safest choice for most commercial machines. We also send PES, EXP, JEF, HUS, VP3, XXX and EMB.

Ready to see your design in 3D puff?

Send your design and the garment, and get a price and a digital proof before you order. There is no account to set up and no minimum order.

Scroll to Top